In this article you can free download BMW INPA (last version, includes NCSExpert and WinKFP).And I will show you how to setup Bmw inpa software steps by steps. In NCS Expert Software 1 comment. As you may or may not know, NCS Expert is simply a program used to read and write (program) parameters to a vehicle. Easycoding for BMW and Rolls-Royce V1.4.0.151112 software download, free Download Rheingold ISTA 4.01.22 standalone on Windows x BMW ISTA+ add BMWAI Coder&Tools for Fxx coding. For BMW E Series Coding Interface = INPA K+DCAN Cable (OBDII to USB) or ICOM ECU Data Files = SP-Daten NCS Expert =. You can to make diagnostics, reset the errors and adapt the of different units and devices of your BMW. – NCS Expert 4.0.1 (with English menus and buttons, and NCS Dummy Profile pre-installed) – NCS Dummy 0.6.0.4 – Tool32 4.0.3 – WinKFP 5.3.1 – Integrated SP-DATEN v53.3 – BMW Coding Tool v2.5.0 (for use as an alternative to NCS Dummy, or to update DATEN files as new ones become available) – USB Drivers for cable.

Here’s little tutorial on BMW E-series coding programs installation.

Disclaimer: The document was translated from Korean. You are at your risk.

Part I. Required files

1. INPA

2. BMW Coding Pack

3. BMW Coding Tool

→ Download E_coding.zip

Unpack and use

4. SP-DATEN

→ Download and use the data file for BASE and car https://mega.nz/#F!ukQzzBwb!bH9cRXpvW4xiTLr-N10CjQ

! iAJg_VqYENXBCaGLS-AvFvhPSNEae2mp-aWtuYOHGv8 (E_coding.zip decryption key)

Part II. Install the INPA program

1. Materials

(1) Coding required cable: BMW INPA K+DCAN cable

(2) Programs required for coding: INPA / NCS Expert

(3) Own vehicle information file (SP-Daten, SP-Daten capacity of 30 ~ 40GB per vehicle)

2. INPA program installation

(1) INPA / K + D CAN drive installation

If you unzip it, there are three folders in Step 1, 2, 3, and there are installation instructions, a description PDF document,

1) Copying the entire EC-Apps under the 01_Step1 directory to C: /

2) Run NFS / Entpackt / disk1 / SETUP.exe under the directory 01_Step1

Install

If not, copy all of these NFS directories to C: / and install them)

Note 1. In Windows 8.1 32bit, copy the file under disk1 to C; /

NTVDM automatically download and run)

Note 2. If the program fails to install again after the installation fails, copy the previously copied C: / EC-Apps

Clear all and copy again

Select Window XP on the screen

The remaining selection values

User mode / Parametrienen einer neuen Configuration ohen Dafer / OBD / KeinApi-Trace / Kein IFH-TRACE / Komfor (.IPO) selection

The first time you install regsvr32, the two * .ocx files will fail to register, but if you uninstall and reinstall the program you just installed from the control panel, the ocx file will be registered normally.

In particular, the message “The program is not installed properly” appears on Windows 7/8. Select the program installed correctly ”

3) Run INSTALL / Instprog.exe under the directory 02_Step2

(Copy and run under C: temp, but not on other drives)

Select “ENGLISH” on the screen, press Continue / Continue and never change the folder or drive to install.

In the Configuration window

Select “Bmw Group Rectification programs UK” → Continue

EDIABAS 6.4.3 → Update

INPA 5.0.1 → Update

NCS Expert 3.0.8 → Check Complete → Continue

Bmw Ncs Expert English Download Windows 7

4) INSTALL / Instprog.exe under the 03_Step3 directory

(Copy and run under C: temp, but not on other drives)

3) in the same way

Old verstion delete → Yes

5) Overwrite inpa.ini under c: / EC-APPS / INPA / CFGDAT with inpa.ini in the INPA folder.

3. Cable connections and port settings

(1) Plug OBD cable into USB port and select manual drive installation

1) Install it as a drive under the drive under the INPA folder, and when installed, recognize USB Serial Port

2) In the USB Serial Port property, set Port Setting / Advanced / Com Port No. 1, Response Time 1

(2) Run Drive_D_CAN_USB / OBDSetup.exe under INPA directory and reboot

INPA installation complete

(3) Confirmation of installation: Execute c: /EC_Apps/INPA/BIN/inpaload.exe and Battery / Ignition

If you see two black dots on the installation succeeded

Part III. Installing BMW Standard Tool from BMW Coding Pack

1. When unzipping, four folders with numbers 1 ~ 4 are created, and BMW Standard Tool 2.12 installation

(Be sure to run the program under BMW Coding Pack folder)

(1) Before running the program, open the Compatibility tab in the properties of the installation file

→ Change Compatibility by selecting Windows XP Service Pack 3 How to download mac os bootable.

(2) Installation file Click “English” in English / German selection window.

(All installation programs will be deleted when English is selected)

(3) Select German / Weiter (Next) “Ich akzeptieredie Vereinbarung”

→ Press “Weiter” 3 times to set the directory (set to 4 folders default) and add 1 folder

(4) Zus? Zliche Aufgaben ausw? Len

→ Check out two of the above four check boxes: “Datensicherung” (data backup)

(Leave the other two checked and press the next one to pop up a popup window)

(5) Leave the STD: OBD default value on the next Hardware Interface screen

(6) COM port number checked in Device Manager 1 Select “COM1” and then USB auf Serial

Adapter Check

(7) Click Next and then click Installer to start the installation

Select “Ignore” if error screen appears and select “Ignore” if error screen appears (error 2)

2. When the installation is complete, go to the 3-UPDATE folder and add three folders (EC-APPS, EDIABAS,

NCSEXPER) whole

Copy to C: → Overwrite existing file with latest English version)

3. After copying the update file, copy the “BMW Coding Shorcuts” folder 4 to the desktop

Part IV. Installing BMW Coding Tools and SP_DATEN

1. Unzip the file into C: / windows / system, C: / windows / system32, C: / windows / Syswow64

Copy comdlg32.ocx, mscomctl.ocx under BMW Coding Tool folder

2. Open a command window in administrator mode and type

(Enter the Windows program app and right-click command to run as administrator)

“Regsvr32 comdlg32.ocx”, “regsvr32 mscomctl.ocx” → After registry registration succeeded

Close the command window and run BMW Coding Tools

3. Press the “Select SP-source” button on the right “SP daten” to find your vehicle information daten file

Select ah Select

4. Click the “UPdate SP-source” button on the right “SP daten” to link and copy the daten file

5. Down the received dummy profile (NCExpert Profile / NCSDUMMY4.PFL) to c: / NCSEXOER / PFL

copy

All programs for E series coding installation is complete.

It is not easy. You must follow each one step by step. Keep the order …

Who Viewed This Article Also Views:

BMW INPA & Ediabas 5.0.2 full English version for BMW from 1998 to 2008 installation tutorial here.

The software CD will come to you with the INPA K+CAN interface, only €17 with free shipping, enjoy shopping here:

This New BMW INPA K+CAN is great designed With FT232RQ Chip has a Switch which turns LEFT is for 7 pin, RIGHT is for 8 pin (8 pin is for K-LINE protocol, old DCAN cable cannot do this).

Note: the guidance especially for Windows XP users.

Before installing, delete all version of INPA-ADS from your computer.

Insert CD to disk E: and open it, there will be a file named “INPACANinstall” which will guide you how to install in detail.

Step1: Open “01_Step1” file in the root of CD disk and copy folder “EC-APPS” onto disk C:

Step2:Run the file “01_Step1NFSEntpacktdisk1SETUP.EXE”

Choose “Windows XP” and click next

Choose “User Mode” and click next

Choose 1 -> OBD ->“Kein API-TRACE” ->“Kein IFH-TRACE” ->“Komfort(.IPO)” and click next

Then press any key to continue

This step Complete

Step3: Run the file “02_Setup2INSTALLInstprog.exe”

Choose English, press continue

While choosing the HDD disk C: for initial setup, do not change, the installation must be on drive C: only, press continue

Choose configuration “BMW Group Rectification Programs UK” and press continue

Activate all spare boxes with:

EDIABAS 6.4.3 – UPDATE

INPA 5.0.1- UPDATE

NCS Expert 3.0.8 – Complete

Press continue to start installation and press End to exit the installation

Step4: Run the file “03_Setup3INSTALLInstprog.exe”

Bmw Ncs Expert Free Download

-Choose English, press continue, press continue again

-While choosing the HDD disk C: for initial setup, do not change, the installation must be on drive C: only, press continue

-Choose configuration “BMW Group Rectification Programs UK” and press continue

-Activate all spare boxes with:

INPA 5.0.1- UPDATE

NCS Expert 3.0.8 – UPDATE

Bmw Ncs Expert

Press continue to start installation and press End to exit the installation

Step5:

Find the file C:EC-APPSINPACFGDAT named “inpa.ini” and replace it with the file “inpa.ini” that is in the root directory of CD disk

Step6: Plug the adapter into spare USB-Port and install drivers manually

Copy the “Driver_D_CAN_USB” file onto disk C:

Choose install from a list of specific location

Select the folder “Driver_D_CAN_USB”

Bmw Ncs Expert Download

You may install the same driver again

Complete driver installation

Then Change the number of COM-port to the value from 5 to 1, also change the value of Latency Timer from 16 to 1.

Step7: open disk C:EDIABASBINEdiabas.ini

In the file “EDIABAS.ini”

“Interface = STD:OBD” must be choosen

Step8: in the file C:WindowsOBD.INI, put the number of USB-COM-port to the value

Step9: Run the file “Driver_D_CAN_USBOBDSetup.exe”

After doing these, you should RE-BOOT the computer

Step10: test

–Connect BMW car with laptop via INPA cable ( via USB Port and OBDII port)

-Turn ignition on

Paint 3d download windows 10. -Run the INPA from: C:EC-APPSINPABINinpaload.exe

-Choose the model of BMW and type of modells you want to see

-Close the soft and disconnect the INPA cable from USB Port each time you change the car connect.

Done!